Show Posts

31

Indoor / Graupner Piper PA18 - Rubber band powered

« on: January 26, 2009, 20:07:25 PM »

Fred

It was very good, and looks too light.
What is the weight?
here also called www.e-voo.com
You can use a translator who was the very time that you wrote that.

abraço

alle

32

Indoor / Alphonse Penaud

« on: January 14, 2009, 19:18:05 PM »

Tentarei construir e voar.

abraço

alle

Try to build and fly.
Anyone else?

abraço

alle

[/img]

33

Indoor / Use of servo motor for propulsion?

« on: December 26, 2008, 20:52:44 PM »

I use the engine of a servant of this propeller 9.
The propeller of 3 inches + - 60 degrees step.
Someone has used this engine for propulsion?
What thrust expected?
I use the same energy as the original servant.

abraço

34

Indoor / hélice de balsa para vôo livre/ propeller of balsa wood for

« on: December 04, 2008, 20:29:44 PM »

Acabei, ficou com 6g, e faltou 2mm para dar 10 polegas de comprimento.
Se tiver ibira terça vou estrear, já tenho um modelo esperando.
não é tão dificil, claro que dá um pouco de trabalho, e não pense que a minha ficou assim tão boa, nas fotos tudo melhora, mas testei, traciona bem e com certa estabilidade.

abrço

alle

I just got, got 6, 2mm and failed to give 10 inches in length.
If you have ibira I will debut Tuesday, already have a model waiting.
is not as difficult, of course it gives a bit of work, and I do not think that was so good in pictures everything improves, but tested, and with some traction and stability, already have a model waiting, I hope that all is with + - 30.

hug

alle

35

Indoor / building the elasticity planne 15g

« on: December 03, 2008, 20:35:41 PM »

Ei ice wind, seu portugês está muito bom, estou começando no vôo livre ainda tenho muito a aprender, tenho um colega que fez a mesma coisa que o seu, segue uma foto e o link de montagem.

abraço

alle

ice wind, his Portuguese is very good, I'm starting at free flight still have a lot to learn, I have a colleague who did the same thing as his own, following a photo and link to assembly.

hug

alle

.

http://www.e-voo.com/forum/viewtopic.php?t=44849

36

Indoor / building the elasticity planne 15g

« on: December 02, 2008, 18:43:57 PM »

É isso mesmo o motor é de borracha, somente a hélice vai ser outra, aquela foto da hélice foi só mostrar o mancal, vou a hélice que está no outro post, desculpe-me pelo ingês ruim.
Voçê disse aluminio?

abraço

alle

That's right the engine is rubber, only the helix going to be another, that photo of the propeller was the only show bearings, I am the propeller that is in another post, excuse me for bad English, is that these are the same, only usually post after flying, not to tips wrong.
You said aluminum? must be pretty hard, and with thirty (30) grams, cool.

hug

alle

37

Indoor / building the elasticity planne 15g

« on: December 01, 2008, 22:24:09 PM »

please comment, accepted suggestions.

hug

alle

38

Indoor / hélice de balsa para vôo livre/ propeller of balsa wood for

« on: December 01, 2008, 22:23:26 PM »

please comment, accepted suggestions.

hug

alle

39

Indoor / hélice de balsa para vôo livre/ propeller of balsa wood for

« on: November 29, 2008, 21:07:23 PM »

Agora é só lixar.

Now it's just sanding.

40

Indoor / hélice de balsa para vôo livre/ propeller of balsa wood for

« on: November 29, 2008, 21:00:12 PM »

A agora é só lixar, dar para ter uma idéia do quanto precisa lixar, segui a dica do Peninha.

The now it's just sanding, to give you an idea of how much needs sanding, follow the tip of the Peninha.

41

Indoor / hélice de balsa para vôo livre/ propeller of balsa wood for

« on: November 29, 2008, 20:55:52 PM »

Precisava de uma maior, não achava, agora vamos a uma nova tentativa.

Largura das ripas 1 polegada
Comprimento das ripas 10 polegadas
Quantidade 6 unid.
Tiradas de uma chapa de balsa 3/32 4A

Na primeira tentativa o passo ficou pouco, aumentei a o número de ripas e diminui a abertura entre elas.

He needed more, not thought, now we are going to have another go.

Width of 1 inch slat
Slat length of 10 inches
Volume 6 units.
Taken from a sheet of balsa 3 / 32 4A

In the first step has been little attempt, increased the number of slat and decreases the opening between them (hint of Cesar)